廣東恒良藍康環保科技有限公司
Foshan Hengliang Metal Equipment Co., Ltd
主頁 Home Page
關於 About
個案欣賞 Previous Cases
主要產品展示 Our Main Products
產品簡介Products Description
地點 Address
聯絡我們 Contact Us
所有分類 - 廣東恒良藍康環保科技有限公司 | 鋁棒自動鋸切 铝灰处理系统 脈沖除塵器
鋁灰處理系統 Aluminium dross processing system
鋁渣處理機通過對熱態鋁渣進行攪拌來分離出液態鋁液,也就是首先對灰渣進行防氧化降溫,同時,再對灰渣進行一定程度的破碎處理,處理後的熱灰加入冷灰桶,對熱灰進行冷卻。利用除塵器進行集中除塵 2台炒灰機共用1套中顆粒冷灰加料系統,其中中顆粒來源全部來自於炒灰機1 2台炒灰機分別配備2台冷灰桶。2套系統可共用外部水循環系統和除塵系統,但是循環量需達到兩台設備需求量的總和 該套設備配備3道篩分系統,其中細灰裝袋後外售,大顆粒鋁含量高,可回爐重新熔化回收 叉車進料出料的位置(圖中標識叉車的位置)在布局時需考慮叉車的回轉空間,理論上需預留7m距離(以3噸叉車為準) 每套炒灰設備配備一套專門的遙控器,簡單方便,亦可在操控箱上手動操作 Through stirring the hot aluminum slag, aluminum liquid is separated by aluminum slag processor. The slag is firstly anti-oxidized and cooled, also, the ash slag is crushed to a certain level. The hot ash is added to the cooling bucket for cooling down. Lastly use dust collector to remove the dust. Two ash frying machines share a set of medium particle cooling feeding system, the source of medium particles comes from machine 1. Two ash frying machines are equipped with two cooling barrels respectively. The 2 sets of systems can share the external water circulation system and dust removal system, but the circulation volume needs to reach the sum of the demand of machines. This set of equipment is equipped with 3 screening systems, the fine ash is bagged and sold, and the large particles have high aluminum content. Each set of ash frying equipment is with a remote.
鋁棒鑄造平台 Automatic aluminum bar saw
自動鋁棒鋸設備參數:(由於是定制設備,詳細請資詢恒良銷售) 鋸切長度:0-~3000㎜ 鋸切範圍:(H*W)50*400 電動機功率:3KW 工作電壓:380V 50HZ 鋸片尺寸:¢400㎜×¢30㎜×3.5×Z120 進給速度:0~3m/min 輸入電源:380V50HZ 工作氣壓:0.6-0.8mpa 耗氣量:180L/min 主軸轉速:無極調速 外型尺寸:長2115mm寬710mm高1365mm Automatic aluminum bar saw equipment parameters: (Because it is a customized equipment, please consult us for details) Sawing length: 0-~3000㎜ Sawing range: (H*W)50*400 Motor power: 3KW Working voltage: 380V 50HZ Saw blade size: ¢400㎜×¢30㎜×3.5×Z120 Feed speed: 0~3m/min Input power: 380V50HZ Working air pressure: 0.6-0.8mpa Air consumption: 180L/min Spindle speed: stepless regulation Dimensions: length 2115mm width 710mm height 1365mm
脈沖除塵器 Industrial Pulse Dust Collector
爐子在投料及耙渣除氣時打開爐門操作,煙氣從爐口排放,爐門關閉進行正常熔煉時爐內壓力為微正壓,爐內產生的煙氣通過爐門的幾個小氣孔或蓄熱式節能燒嘴的排風機排放。 熔煉爐及鋁灰處理設備在加料、除氣、耙渣、炒灰工作階段會產生的煙氣量較大。如不經處理排放,會嚴重影響周邊環境及損害員工的身體健康,因此必須配套相應的環保除塵設備,使煙氣通過處理後排放達到國家排放要求。 設計範圍為:風量設計,煙塵捕集裝置,除塵器,風電機匹配,排煙管道系統、電氣控制系統等設計。 二、設計依據 2.1、《冶金工業環境保護設計規定》 (YB9066-95) 2.2、《采暖通氣和空氣調節設計規範》 (GBJ19-88) 2.3、《再生銅、鋁、鉛、鋅工業污染物排放標準》(GB 31574-2015) 2.4、《工業企業設計衛生標準》 (TJ36-79) 2.5、各工況點的實際情況 本除塵器系統可收集熔爐(每次一個爐加料)及鋁灰處理煙塵,爐口集塵罩和鋁灰處理系統產生的煙塵。處理指標:排放濃度 ≤10mg/Nm3、除塵效率≥99.5%、煙塵捕集率≥90%,林格曼黑度≤1級。 The scope of design is: air volume design, dust collection device, dust collector, wind motor matching, exhaust pipe system, electrical control system, etc. The dust collector system can collect fumes from melting furnaces (one furnace is charged at a time) and aluminum ash processing, dust collection hoods at the furnace mouth and aluminum ash processing systems. Treatment indicators: emission concentration ≤10mg/Nm3, dust removal efficiency ≥99.5%, soot collection rate ≥90%, Ringelmann blackness ≤1.
鋁液自動精煉罐 Automatic refining tank
自動精煉罐通過變頻調變和精煉氣均勻的把輔助材料均勻地註入鋁液,用於變形鋁及鋁合金的精煉,可有效除去熔體中的氧化夾雜和氫氣。全不銹鋼圓桶可裝入(40-60kg)精煉劑,排氣均勻提高鋁棒質量和工作效益。 Through frequency modulation and refining gas let the auxiliary materials evenly injecting into the molten aluminum, it can be used for refining of aluminum and aluminum alloys, so as to effectively remove oxidation inclusions and hydrogen. The all-stainless steel drum can be filled with (40-60kg) refining agent. As a result, the exhaust improves the quality of aluminum rods and raise work efficiency.
主要產品展示
Our Main Products
聯系我們
聯系我們
Cookie的使用
我們使用cookies來確保流暢的瀏覽體驗。若繼續,我們會認爲你接受使用cookies。
確認
了解更多